Arden Hills, MN · the Upper Midwest
Arden Hills, MN Switchgear Buyers
Sale your Electrical Switchgear now !
- Paid before pickup
- No testing required
- Freight and rigging covered
- Any amperage, any condition
Request a Quote
We buy switchgear in Arden Hills, MN and throughout Minnesota. There is no obligation.
Why Sellers Choose Us
What an Arden Hills switchgear sale involves on your end
Funds change hands before a single section leaves your property. There is no consignment and no waiting on a downstream resale.
You are never asked to test, energize, clean or repair the gear. Our team evaluates it from the nameplate photos and our own inspection.
Lowboys, flatbeds, cribbing, section separation and permits are billed to us. That cost is already priced into the offer you receive.
Disconnection coordination, dismantling, rigging out of the electrical room and loading are performed by our crews at our expense.
Switchgear We Buy in Arden Hills
Every class is in scope, from branch panelboards to metal-clad medium voltage lineups
The Arden Hills Market
We have been buying switchgear out of the Upper Midwest for years, and Arden Hills is well inside the lanes our trucks already run. This is a Minnesota pickup for us, staged out of Minneapolis and covered end to end. Payment is upfront. You do not front the freight, you do not pay a rigger, and you do not need to have the gear tested before we commit to a price.
Every class of distribution equipment is in scope. What we see most often in Arden Hills is molded case breakers by the pallet, untested and 5kV magnetic air breaker sections on skids. Across Minnesota we also buy motor control centers with full starter buckets, unit substations with the primary and secondary attached and panelboards in bulk lots off a gut renovation.
Who We Buy From
Our sellers here are typically pulp, paper and lumber mills, industrial auctioneers with unsold lots, electrical supply houses moving old inventory. We also buy from oil and gas service yards and solar and wind EPC firms with leftover equipment.
The reasons vary less than you would expect:
- Spare breakers were purchased years ago for a project that never proceeded.
- The building changed hands and the electrical equipment transferred with the property.
- A flood or storm replacement has arrived and the damaged gear needs to be removed.
- A cancelled or downsized build left new gear crated and never installed.
Pickup and Freight in Arden Hills
Arden Hills is an easy run for us off the Minneapolis lane, which keeps our freight cost down and our offer up. If a utility disconnect has to happen first, we can coordinate the timing with your electrician.
The gear is valued on its own merits. The cost of getting it out of Arden Hills is absorbed on our side. Sellers who already hold a scrap quote often find the difference substantial, because a scrap figure deducts hauling and ignores what the breakers, buckets and bus are worth to somebody who needs them.
Common Minnesota Equipment
Switchboards
Front-accessible service entrance and distribution switchboards from commercial buildings.
Switchgear Scrap
Burned, gutted, flooded and unrepairable gear bought for copper and metal content.
Medium Voltage Switchgear
5kV and 15kV class metal-clad lineups with vacuum or air breakers, indoor and outdoor.
Bus Plugs and Busway
Plug-in and feeder busway runs, elbows, tees and bus plugs from industrial ceilings.
Quote an Arden Hills Lineup
Send a nameplate photo and receive a firm number, usually the same day.
How the Sale Works
Four steps, none of which cost you anything
Send What You Have
A photograph of the nameplate and one wide shot down the front of the lineup is enough to begin. If the nameplate is gone, photograph the gear anyway and we will work from the construction, the bus and the breaker frames.
Receive a Firm Offer
We respond with a committed cash figure, usually the same day. It is an offer rather than an estimate, and it does not move afterward.
Schedule on Your Terms
Pickup in Arden Hills is arranged around your outage window, plant shutdown or building access hours. Where a utility disconnect has to happen first, we coordinate the timing.
We Pay, Then We Haul
Payment is completed before anything moves. Our crew performs the teardown, the section separation, the rigging and the loading, and our truck removes it.
Also Buying Across Minnesota
We cover 178 locations in Minnesota.
Selling Switchgear in Arden Hills: Common Questions
Straight answers
Do you actually come to Arden Hills to pick up switchgear?
Yes. Arden Hills is an easy run for us off the Minneapolis lane, which keeps our freight cost down and our offer up. We do not ask you to arrange freight, separate sections or deliver anything to us.
Do I need to have the gear tested first?
No. Testing is never a condition of our offer. We assess a lineup from photos, the nameplate and our own inspection at pickup.
What if the breakers have already been pulled out?
We still buy it. A complete lineup with its breakers installed is worth more, but empty structures have real value in bus and steel, and loose breakers sitting on a shelf are worth quoting on their own. Tell us what is still there and what has already gone.
When do I get paid?
Before anything leaves your property. Payment is not contingent on us reselling the equipment afterward.
Will you buy a single section in Arden Hills, or only full lineups?
Both. One switchboard section is worth a call, and if you have a full electrical room or several buildings coming down we will quote the entire lot as one purchase.
What if the lineup is still energized and in service?
That is normal. Tell us and we will coordinate the disconnection timing with your electrician or the utility, then handle the teardown and rigging ourselves.
Have Switchgear in Arden Hills to Sell?
Call or text a nameplate photo and we will return a firm offer, usually the same day.
Ready to Sell?
Send a nameplate photo and we will return a firm cash number for your Arden Hills switchgear.