Austin, TX · Texas
Sell Your Switchgear in Austin, TX
Sale your Electrical Switchgear now !
- Paid before pickup
- No testing required
- Freight and rigging covered
- Any amperage, any condition
Request a Quote
We buy switchgear in Austin, TX and throughout Texas. There is no obligation.
Why Sellers Choose Us
What an Austin switchgear sale involves on your end
Funds change hands before a single section leaves your property. There is no consignment and no waiting on a downstream resale.
You are never asked to test, energize, clean or repair the gear. Our team evaluates it from the nameplate photos and our own inspection.
Lowboys, flatbeds, cribbing, section separation and permits are billed to us. That cost is already priced into the offer you receive.
Disconnection coordination, dismantling, rigging out of the electrical room and loading are performed by our crews at our expense.
Switchgear We Buy in Austin
Every class is in scope, from branch panelboards to metal-clad medium voltage lineups
The Austin Market
Old switchgear pulled anywhere in Austin gets bought outright here, including lineups nobody bothered to test. Texas sellers get the same terms as anywhere else we operate: paid first, freight on us. We will work around your outage window, your plant schedule or your landlord's access hours. Pickup gets scheduled to suit you.
Every class of distribution equipment is in scope. What we see most often in Austin is 4000A paralleling switchgear from a standby plant and motor control centers with full starter buckets. Across Texas we also buy MCC sections with VFD buckets still installed, 3000A drawout switchgear pulled during a service upgrade and loose drawout air breakers on pallets.
Who We Buy From
Our sellers here are typically demolition crews stripping a site, industrial auctioneers with unsold lots, general contractors on an adaptive-reuse project. We also buy from electrical supply houses moving old inventory and utility contractors with surplus stock.
Most sales trace back to one of a few situations:
- An arc flash study recommended replacing gear that was past its maintainable life.
- A cancelled or downsized build left new gear crated and never installed.
- Spare breakers were purchased years ago for a project that never proceeded.
- A flood or storm replacement has arrived and the damaged gear needs to be removed.
Pickup and Freight in Austin
We stage flatbeds and lowboys near Dallas and dispatch into Austin as loads fill. If the lineup is in a basement electrical room or up a ramp, tell us and we will bring the right rigging.
The gear is valued on its own merits. The cost of getting it out of Austin is absorbed on our side. Sellers who already hold a scrap quote often find the difference substantial, because a scrap figure deducts hauling and ignores what the breakers, buckets and bus are worth to somebody who needs them.
Common Texas Equipment
Unit Substations
Close-coupled primary, transformer and secondary assemblies from industrial plants.
Arc-Resistant Switchgear
Type 2B arc-resistant lineups with plenums and pressure relief, low and medium voltage.
Outdoor Switchgear
Walk-in and non-walk-in weatherproof enclosures, pad-mounted and skid-mounted lineups.
Medium Voltage Switchgear
5kV and 15kV class metal-clad lineups with vacuum or air breakers, indoor and outdoor.
Quote an Austin Lineup
Send a nameplate photo and receive a firm number, usually the same day.
How the Sale Works
Four steps, none of which cost you anything
Send What You Have
A photograph of the nameplate and one wide shot down the front of the lineup is enough to begin. If the nameplate is gone, photograph the gear anyway and we will work from the construction, the bus and the breaker frames.
Receive a Firm Offer
We respond with a committed cash figure, usually the same day. It is an offer rather than an estimate, and it does not move afterward.
Schedule on Your Terms
Pickup in Austin is arranged around your outage window, plant shutdown or building access hours. Where a utility disconnect has to happen first, we coordinate the timing.
We Pay, Then We Haul
Payment is completed before anything moves. Our crew performs the teardown, the section separation, the rigging and the loading, and our truck removes it.
Also Buying Across Texas
We cover 490 locations in Texas.
Selling Switchgear in Austin: Common Questions
Straight answers
Do you actually come to Austin to pick up switchgear?
Yes. We stage flatbeds and lowboys near Dallas and dispatch into Austin as loads fill. We do not ask you to arrange freight, separate sections or deliver anything to us.
Do I need to have the gear tested first?
No. Testing is never a condition of our offer. We assess a lineup from photos, the nameplate and our own inspection at pickup.
What if the breakers have already been pulled out?
We still buy it. A complete lineup with its breakers installed is worth more, but empty structures have real value in bus and steel, and loose breakers sitting on a shelf are worth quoting on their own. Tell us what is still there and what has already gone.
When do I get paid?
Before anything leaves your property. Payment is not contingent on us reselling the equipment afterward.
Will you buy a single section in Austin, or only full lineups?
Both. One switchboard section is worth a call, and if you have a full electrical room or several buildings coming down we will quote the entire lot as one purchase.
What if the lineup is still energized and in service?
That is normal. Tell us and we will coordinate the disconnection timing with your electrician or the utility, then handle the teardown and rigging ourselves.
Have Switchgear in Austin to Sell?
Call or text a nameplate photo and we will return a firm offer, usually the same day.
Ready to Sell?
Send a nameplate photo and we will return a firm cash number for your Austin switchgear.