Bothell, WA · the Pacific Northwest
Bothell, WA: Sell Us Your Switchgear
Sale your Electrical Switchgear now !
- Paid before pickup
- No testing required
- Freight and rigging covered
- Any amperage, any condition
Request a Quote
We buy switchgear in Bothell, WA and throughout Washington. There is no obligation.
Why Sellers Choose Us
What a Bothell switchgear sale involves on your end
Funds change hands before a single section leaves your property. There is no consignment and no waiting on a downstream resale.
You are never asked to test, energize, clean or repair the gear. Our team evaluates it from the nameplate photos and our own inspection.
Lowboys, flatbeds, cribbing, section separation and permits are billed to us. That cost is already priced into the offer you receive.
Disconnection coordination, dismantling, rigging out of the electrical room and loading are performed by our crews at our expense.
Switchgear We Buy in Bothell
Every class is in scope, from branch panelboards to metal-clad medium voltage lineups
The Bothell Market
There is a resale market for the switchgear sitting idle at your Bothell site, and we pay against that market rather than scrap weight. Washington sellers get the same terms as anywhere else we operate: paid first, freight on us. We quote from photos and a nameplate, pay on pickup, and cover the rigging and freight ourselves.
Every class of distribution equipment is in scope. What we see most often in Bothell is motor control centers with full starter buckets and loose drawout air breakers on pallets. Across Washington we also buy 3000A drawout switchgear pulled during a service upgrade, 15kV metal-clad lineups with vacuum breakers and 2000A main-tie-main lineups from a light industrial park.
Who We Buy From
Our sellers here are typically industrial auctioneers with unsold lots, hospital and campus engineering groups, plant maintenance managers after a service upgrade. We also buy from demolition crews stripping a site and electrical contractors clearing out a job trailer.
Most sales trace back to one of a few situations:
- An arc flash study recommended replacing gear that was past its maintainable life.
- The manufacturer discontinued the line, so parts support ended and the lineup was replaced wholesale.
- The plant closed and remaining assets are being liquidated.
- Service capacity was upsized, leaving the previous gear as an unneeded spare.
Pickup and Freight in Bothell
We stage flatbeds and lowboys near Seattle and dispatch into Bothell as loads fill. If the lineup is in a basement electrical room or up a ramp, tell us and we will bring the right rigging.
The gear is valued on its own merits. The cost of getting it out of Bothell is absorbed on our side. Sellers who already hold a scrap quote often find the difference substantial, because a scrap figure deducts hauling and ignores what the breakers, buckets and bus are worth to somebody who needs them.
Common Washington Equipment
Unit Substations
Close-coupled primary, transformer and secondary assemblies from industrial plants.
Circuit Breakers
Loose air, vacuum, insulated case and molded case breakers, individually or by the pallet.
Low Voltage Switchgear
600V class drawout and fixed-mounted lineups pulled from indoor electrical rooms.
Motor Control Centers
MCC lineups with starter buckets, VFDs and combination starters from plants and utilities.
Quote a Bothell Lineup
Send a nameplate photo and receive a firm number, usually the same day.
How the Sale Works
Four steps, none of which cost you anything
Send What You Have
A photograph of the nameplate and one wide shot down the front of the lineup is enough to begin. If the nameplate is gone, photograph the gear anyway and we will work from the construction, the bus and the breaker frames.
Receive a Firm Offer
We respond with a committed cash figure, usually the same day. It is an offer rather than an estimate, and it does not move afterward.
Schedule on Your Terms
Pickup in Bothell is arranged around your outage window, plant shutdown or building access hours. Where a utility disconnect has to happen first, we coordinate the timing.
We Pay, Then We Haul
Payment is completed before anything moves. Our crew performs the teardown, the section separation, the rigging and the loading, and our truck removes it.
Also Buying Across Washington
We cover 222 locations in Washington.
Selling Switchgear in Bothell: Common Questions
Straight answers
Do you actually come to Bothell to pick up switchgear?
Yes. We stage flatbeds and lowboys near Seattle and dispatch into Bothell as loads fill. We do not ask you to arrange freight, separate sections or deliver anything to us.
Do I need to have the gear tested first?
No. Testing is never a condition of our offer. We assess a lineup from photos, the nameplate and our own inspection at pickup.
What if the breakers have already been pulled out?
We still buy it. A complete lineup with its breakers installed is worth more, but empty structures have real value in bus and steel, and loose breakers sitting on a shelf are worth quoting on their own. Tell us what is still there and what has already gone.
When do I get paid?
Before anything leaves your property. Payment is not contingent on us reselling the equipment afterward.
Will you buy a single section in Bothell, or only full lineups?
Both. One switchboard section is worth a call, and if you have a full electrical room or several buildings coming down we will quote the entire lot as one purchase.
What if the lineup is still energized and in service?
That is normal. Tell us and we will coordinate the disconnection timing with your electrician or the utility, then handle the teardown and rigging ourselves.
Have Switchgear in Bothell to Sell?
Call or text a nameplate photo and we will return a firm offer, usually the same day.
Ready to Sell?
Send a nameplate photo and we will return a firm cash number for your Bothell switchgear.